RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049314 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM UPPER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

HINT:: ·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

PROCEDURE

Hide Display 1.TABLE OF BOLT, SCREW AND NUT

HINT:: All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

0.177,0.448 0.792,0.646 0.615,0.198 10 Code 3.688,0.448 4.458,0.646 0.771,0.198 10 Shape 5.917,0.448 6.688,0.646 0.771,0.198 10 Shape 2.583,0.448 3.198,0.646 0.615,0.198 10 Code 4.844,0.448 5.458,0.646 0.615,0.198 10 Code 0.219,1.292 0.677,1.49 0.458,0.198 10 <A> 2.615,1.271 3.073,1.469 0.458,0.198 10 <B> 4.875,1.26 5.333,1.458 0.458,0.198 10 <C> 0.219,2.188 0.677,2.385 0.458,0.198 10 <D> 2.01,0.948 2.323,1.146 0.313,0.198 10 φ 5 1.885,2.052 2.958,2.25 1.073,0.198 10 (0.236) 1.885,1.563 2.958,1.76 1.073,0.198 10 (0.551) 1.906,1.365 2.521,1.563 0.615,0.198 10 L = 14 4.281,0.948 4.594,1.146 0.313,0.198 10 φ 8 4.177,1.146 5.25,1.344 1.073,0.198 10 (0.315) 4.188,1.365 4.802,1.563 0.615,0.198 10 L = 21 4.177,1.563 5.25,1.76 1.073,0.198 10 (0.827) 6.552,0.948 6.865,1.146 0.313,0.198 10 φ 6 6.458,1.563 6.906,1.76 0.448,0.198 10 (0.787) 6.469,1.365 7.083,1.563 0.615,0.198 10 L = 20 6.458,1.146 6.906,1.344 0.448,0.198 10 (0.236) 2.01,1.844 2.323,2.042 0.313,0.198 10 φ 6 1.885,1.156 2.958,1.354 1.073,0.198 10 (0.197) 1.906,2.292 2.521,2.49 0.615,0.198 10 L = 16 1.885,2.5 2.958,2.698 1.073,0.198 10 (0.630) 1.323,0.448 2.094,0.646 0.771,0.198 10 Shape 5.344,0.042 6.677,0.229 1.333,0.188 10 mm (in.) (L = Length)

Hide Display 2. PRECAUTION

NOTICE:: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.; Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION201212,201410,_V1,_008731,_0049918,RM1000000004DZ6,201410,201504,_V1,_008731,_0049918,RM100000000HFP9,201504,999999,_V1,_008731,_0049918,RM100000000JQM7,

Hide Display 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:: When disconnecting the cable, some systems need to be initialized after the cable is reconnected.; Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION201212,201311,_V1,_008731,_0049918,RM1000000004DZ8,201311,201410,_V1,_008731,_0049918,RM100000000C1G2,201410,201504,_V1,_008731,_0049918,RM100000000HFOT,201504,999999,_V1,_008731,_0049918,RM100000000JQM8,

Hide Display 55412C 4.REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

Apply protective tape as shown in the illustration.

Using moulding remover B, detach the 6 clips and 2 claws in the order shown in the illustration and remove the center No. 1 instrument cluster finish panel.

4.563,1.188 4.771,1.385 0.208,0.198 10 true (1) 4.365,1.354 4.594,1.552 0.229,0.198 10 true (2) 4.01,1.417 4.26,1.604 0.25,0.188 10 true (3) 3.615,1.094 3.823,1.281 0.208,0.188 10 true (4) 3.396,1.5 3.615,1.688 0.219,0.188 10 true (5) 3.104,1.583 3.323,1.781 0.219,0.198 10 true (6) 2.854,1.667 3.073,1.854 0.219,0.188 10 true (7) 2.615,1.792 2.833,1.969 0.219,0.177 10 true (8)

Protective Tape

Hide Display 55670 5.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

0.156,0.375 0.313,0.573 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Using moulding remover B, detach the 2 clips and 2 claws and remove the No. 3 instrument panel register assembly.

Hide Display 55680A 6.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

1.969,0.573 2.125,0.771 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Using moulding remover B, detach the 3 clips and claw and remove the No. 4 instrument panel register assembly.

Hide Display 83950M 7.REMOVE TELLTALE LIGHT ASSEMBLY

Click hereVehicle Interior>METER / GAUGE / DISPLAY>CLOCK>REMOVAL201212,999999,_58,_008784,_0049184,RM10000000047C2_01_0002,

Hide Display 55521C 8.REMOVE STEREO OPENING COVER (w/o Audio)

1.802,1.292 1.958,1.49 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Remove the 4 bolts.

Detach the 4 clips and remove the stereo opening cover.

Hide Display 86120 9.REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL201212,201311,_56,_008775,_0049775,RM1000000004CLD_01_0005,201311,999999,_56,_008775,_0049775,RM100000000BNCV_01_0005,

Hide Display 10.REMOVE NAVIGATION RECEIVER (w/ Navigation System)

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL201212,201311,_56,_008776,_0050609,RM1000000004G9R_01_0005,201311,999999,_56,_008776,_0050609,RM100000000BMVX_01_0005,

Hide Display 55411G 11.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL

2.177,2.24 2.333,2.438 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Using moulding remover B, detach the claw and 11 clips and remove the No. 1 instrument cluster finish panel.

Hide Display 83100 12.REMOVE COMBINATION METER ASSEMBLY

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL201212,999999,_58,_008784,_0049183,RM10000000047BX_02_0005,

Hide Display 13.REMOVE HEADLIGHT DIMMER SWITCH

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL201212,999999,_59,_008430,_0050196,RM1000000004EPC,

Hide Display 55406B 14.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except Automatic Air Conditioning System)

1.323,1.969 1.479,2.167 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Detach the 2 clips and remove the lower center instrument cluster finish panel sub-assembly.

Disconnect each connector.

Hide Display 55900 15.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Automatic Air Conditioning System)>REMOVAL201212,999999,_58,_008789,_0050037,RM1000000004DY0_01_0014,

Hide Display 55012A 16.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Using moulding remover B, detach the 13 clips and remove the No. 2 instrument panel garnish sub-assembly.

for LHD with Entry and Start System:

Disconnect the connector.

Hide Display 55421B 17.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL

Using moulding remover B, detach the 4 clips and remove the upper instrument cluster finish panel.

Hide Display 55550 18.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

2.031,1.448 2.198,1.688 0.167,0.24 10 false . 1.969,1.417 2.125,1.615 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Disconnect the glove compartment door stopper sub-assembly.

Slightly bend the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it is horizontal.

2.021,1.583 2.177,1.781 0.156,0.198 10 false .

Protective Tape

Pull the glove compartment door assembly toward the rear of the vehicle to detach the 2 hinges and remove it.

Hide Display 55535B 19.REMOVE NO. 2 SPEAKER HOLE COVER (w/o Speaker)

2.063,1.354 2.219,1.552 0.156,0.198 10 false .

Protective Tape

Apply protective tape as shown in the illustration.

Using moulding remover B, detach the 2 clips, 2 claws and 2 guides and remove the No. 2 speaker hole cover.

Hide Display 55525 20.REMOVE NO. 1 SPEAKER HOLE COVER (w/o Speaker)

HINT:: Use the same procedure described for the No. 2 speaker hole cover.

Hide Display 55535B 21.REMOVE NO. 2 SPEAKER HOLE COVER (w/ Speaker)

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL201212,201311,_56,_008775,_0049965,RM1000000004DL2_01_0005,201311,999999,_56,_008775,_0049965,RM100000000BMWJ_01_0005,

Hide Display 55525 22.REMOVE NO. 1 SPEAKER HOLE COVER (w/ Speaker)

HINT:: Use the same procedure described for the No. 2 speaker hole cover.

Hide Display 86160P 23.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (w/ Speaker)

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL201212,201311,_56,_008775,_0049965,RM1000000004DL2_01_0004,201311,999999,_56,_008775,_0049965,RM100000000BMWJ_01_0004,

Hide Display 62212 24.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL201212,999999,_58,_008791,_0049317,RM10000000048W9_01_0077,

Hide Display 62211 25.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL201212,999999,_58,_008791,_0049317,RM10000000048W9_01_0078,

Hide Display 62212 26.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL201212,999999,_58,_008791,_0049317,RM10000000048W9_01_0111,

Hide Display 62211 27.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL201212,999999,_58,_008791,_0049317,RM10000000048W9_01_0112,

Hide Display 28.REMOVE UPPER INSTRUMENT PANEL

1.375,0.406 1.677,0.406 1.677,0.406 1.854,0.938 true 1.219,0.333 1.531,0.531 0.313,0.198 10 *1

*1	Lock Slider
	Pull

for Single Type Airbag:

Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the airbag connector.

NOTICE:: When handling the airbag connector, take care not to damage the airbag wire harness.

ii.

Disconnect each connector.

iii.

Remove the 2 bolts <B>.

iv.

Remove the 2 bolts <C> or <D>.

5.042,4.427 5.583,4.427 5.583,4.427 5.802,4.552 true 5.177,4.74 5.177,4.427 true 4.344,5.219 4.5,5.219 4.5,5.219 4.531,5.063 true 1.323,0.917 1.531,0.917 1.531,0.917 1.677,1.031 true 5.917,0.938 5.656,0.938 5.656,0.938 5.521,1.052 true 4.854,4.354 5.167,4.552 0.313,0.198 10 *1 4.188,5.146 4.5,5.344 0.313,0.198 10 *3 5.927,0.854 6.24,1.052 0.313,0.198 10 *2 1.177,0.833 1.49,1.031 0.313,0.198 10 *2

*1	Bolt <B>	*2	Bolt <C> or <D>
*3	Airbag Connector	-	-

0.906,1.99 0.604,1.99 0.604,1.99 0.531,1.51 true 1.104,0.896 0.802,0.896 0.802,0.896 0.729,0.417 true 0.052,1.01 0.365,1.208 0.313,0.198 10 *2 0.052,0.063 0.365,0.26 0.313,0.198 10 *1 1.146,0.802 1.458,1 0.313,0.198 10 *3 0.948,1.896 1.26,2.094 0.313,0.198 10 *3

*1	Airbag Connector A
*2	Airbag Connector B
*3	Lock Slider
	Pull

for Dual Type Airbag:

Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the 2 airbag connectors A and B.

NOTICE:: When handling the airbag connector, take care not to damage the airbag wire harness.

ii.

Disconnect each connector.

iii.

Remove the 2 bolts <B>.

iv.

Remove the 2 bolts <C> or <D>.

4.99,5.094 5.302,5.292 0.313,0.198 10 *1 1.646,0.583 1.958,0.781 0.313,0.198 10 *2 4.573,4.542 4.885,4.74 0.313,0.198 10 *4 5.396,0.583 5.708,0.781 0.313,0.198 10 *2 5.625,4.865 5.938,5.063 0.313,0.198 10 *1 4.49,5.177 4.802,5.375 0.313,0.198 10 *3

*1	Bolt <B>	*2	Bolt <C> or <D>
*3	Airbag Connector A	*4	Airbag Connector B

Pull up the upper instrument panel to detach the 8 clips and remove it.

FaceBox